Products

Inflate, Deflate, and Equalize air pressure in up to 6 tires, all at once. See all of the uses below:

• Air up 1 to 6 tires simultaneously (Less stress on your compressor!)
• Air down 1 to 6 tires simultaneously (Less stress on you!)
• Check all of the tires’ PSI from one spot (No more continuously bending over checking PSIs)
• Move air from a spare tire into other tires
• Effortlessly equalize tire pressures
• Make all 4-6 tires the same pressure
• Run different PSI in the front tires from the back tires
• 1-150 psi, 1% accuracy, .1psi precision, back lit digital gauge
• This version fits up to a 200″ wheelbase with the air source in the middle of the front or rear bumper areas
• If you need a shorter wheelbase, check out the MORRFlate Quad Off Road 4 Tire Inflation Deflation Kit
• If your air source is in a different location, check out our MORRFlate Extensions
• All MORRFlates fit ARB and PowerTank fittings “plug n play” If you have a Smittybilt, Viaire, Warn Powerplant, or something modeled after those, you will need a MORRFlate Adapter Kits.
• Read the entire MORRFlate Off Road 4 Tire Inflation Deflation Kit article for more detailed information!

Inflate, Deflate, and Equalize air pressure in all 4 tires, all at once. See all of the uses below:

• Air up 1 to 4 tires simultaneously (Less stress on your compressor!)
• Air down 1 to 4 tires simultaneously (Less stress on you!)
• Check all of the tires’ PSI from the manifold (No more continuously bending over checking PSIs)
• Move air from a spare tire into other tires
• Effortlessly equalize tire pressures
• Run different PSI in the front tires from the back tires
• 1-150 psi, 1% accuracy, .1psi precision, back lit digital gauge
• This version fits up to a 125″ wheelbase with the air source in the middle of the front or rear bumper areas, or in the center of the side of the vehicle (under seat mounted compressors).
• If you need a longer wheelbase, check out the MORRFlate Quad+ Off Road 4 Tire Inflation Deflation Kit
• If your air source is in a different location, check out our MORRFlate Extensions
• All MORRFlates fit ARB compressors and PowerTanks “plug n play” If you have a Smittybilt, Viaire, Warn Powerplant, or something modeled after those, you will need a MORRFlate Adapter Kits.
• Read the entire MORRFlate Off Road 4 Tire Inflation Deflation Kit article for more detailed information!

Inflate, Deflate, and Equalize air pressure in all 4 tires, all at once. See all of the uses below:

• Air up 1 to 4 tires simultaneously (Less stress on your compressor!)
• Air down 1 to 4 tires simultaneously (Less stress on you!)
• Check all of the tires’ PSI from the manifold (No more continuously bending over checking PSIs)
• Move air from a spare tire into other tires
• Effortlessly equalize tire pressures
• Run different PSI in the front tires from the back tires
• 1-150 psi, 1% accuracy, .1psi precision, back lit digital gauge
• This fits up to155″ wheelbases. To find your wheelbase, measure the distance between your front and rear axle.
• If you need a longer wheelbase, check out the MORRFlate Mega Quad Off Road 4 to 6 Tire Inflation Deflation Kit
• If your air source is in a different location, check out our MORRFlate Extensions
• All MORRFlates fit ARB compressors and PowerTanks “plug n play” If you have a Smittybilt, Viaire, Warn Powerplant, or something modeled after those, you will need a MORRFlate Adapter Kits.
• Read the entire MORRFlate Off Road 4 Tire Inflation Deflation Kit article for more detailed information!

• 10.6 CFM dual cylinder compressor at 0 PSI
• 6.5 CFM at 30 psi
• 150 psi rated
• PSI Cutoff Switch (80psi on, 120psi off)
• Thermal Cutoff Switch & Purge Valve
• 80% duty cycle @ 0psi (45min on, 10min off) (6-8 vehicles) (see duty cycle chart)
• 12v, 90amps peak, ~50amp running
• 14x7x9″ external dimensions
• 70-75 dB noise level from 1ft distance
• Beefed up carrying bag with accessory pockets
• Threaded filter caps so the compressor can now be mounted in any direction/orientation (except upside down)
• USA Standard color matched air fitting – Push-to-connect “Universal” Coupler (Works with 1/4″ Industrial, Auto, or Aro fittings)
• WARNING: Compressors get hot! Recommended to wear the included MORRFlate Groovy Gloves while disconnecting air fittings.
• Since the TenSix™ is rated for 10.6 CFM, it is highly recommended to use with a MORRFlate 4 Tire Inflation & Deflation™ Kit to avoid back pressures on the compressor from filling 1 tire at a time.

Gen2 Upgrades (Also, now unique to only MORRFlate):

• Stainless Steel Outlet Hose (for better heat dissipation and heat sinking)
• Purge Valve (to release the internal pressures when done)
• Resized Aluminum heat sinks (upgraded from ABS so they actually fit the cylinders and works as a heat sink)
• Internal aluminum cylinders (upgraded from mild steel to dissipate heat better)
• New piston rings (better material for wear and heat resistance longevity).

Note About This Product: This compressor is not designed for 1 tire at a time. You can still air up a single flat if you need to, but the duty cycle dwindles to 8-10min doing 1 tire at a time. Airing up an entire vehicle, 1 tire at a time, will damage the TenSix. It just simply puts out too much air and is optimized for 4 tires at a time.

Set Your Pressure™!

• Air up a set of 35″ tires from 10 to 40 psi in under 5min (when combined with a 4 Tire Hose Kit)
• 10.6 CFM dual cylinder compressor at 0 PSI
• 6.5 CFM at 30 psi
• 10-120 psi in Auto Mode
• 1-150 psi in Manual Mode
• Thermal Cutoff Switch & Purge Valve
• 80% duty cycle @ 0psi (45min on, 10min off) (6-8 vehicles) (see duty cycle chart)
• 12v, 90amps peak, ~50amp running
• 14x7x9″ external dimensions
• 70-75 dB noise level from 1ft distance
• Beefed up carrying bag with accessory pockets
• Threaded filter caps so the compressor can be mounted in any direction/orientation (except upside down)
• USA Standard color matched air fitting – Push-to-connect “Universal” Coupler (Works with 1/4″ Industrial, Auto, or Aro fittings)
• WARNING: Compressors get hot! Recommended to wear the included MORRFlate Groovy Gloves while disconnecting air fittings.
• Since the TenSix™ is rated for 10.6 CFM, it is highly recommended to use with a MORRFlate 4 Tire Inflation & Deflation™ Kit to avoid back pressures on the compressor from filling 1 tire at a time.

Gen2 Upgrades (Also, now unique to only MORRFlate):

• Stainless Steel Outlet Hose (for better heat dissipation and heat sinking)
• Purge Valve (to release the internal pressures when done)
• Resized Aluminum heat sinks (upgraded from ABS so they actually fit the cylinders and works as a heat sink)
• Internal aluminum cylinders (upgraded from mild steel to dissipate heat better)
• New piston rings (better material for wear and heat resistance longevity).

Note About This Product: This compressor is not designed for 1 tire at a time. You can still air up a single flat if you need to, but the duty cycle dwindles to 8-10min doing 1 tire at a time. Airing up an entire vehicle, 1 tire at a time, will damage the TenSix. It just simply puts out too much air and is optimized for 4 tires at a time.

The Reign 270 FR awning is a self supporting 270 degree awning. Easily deployed in under a minute by just one person.

-Powder coated aluminum with stainless steel hardware, including the backside mounting plate. No unsightly raw aluminum

-600D flame resistant (FR), waterproof ripstop oxford material. The FR awning fabric provides extra piece of mind whether you are cooking or welding near the awning. Awning fabric is grey with an olive green outer edge and navy blue accents

-Squared-off design provides full coverage at the rear of the vehicle for more usable space

-Tension strap at the edge of the awning to accommodate a wide array of vehicles and campers

-Packed dimensions - 94” L x 6” W x 7” T

-Weight - 44 lbs - one of the lightest 270’s on the market!

-83 sq ft (7.7 sq meters) of coverage

-Truss style arms provide strength while staying light weight

-Three support legs are included and secure up and out of the way on the awning arms

-Flip up rain peak

-700G PVC travel cover

-Three versatile mounting brackets, ground pegs, reflective guy wires and M8 stainless steel hardware included. Attaches to load bars, platforms and any rack with t-track

-Full perimeter Velcro strip for optional Annex Walls, Windbreaker and Accessory Panels

-Tie down points on each corner and the center of each gap for drainage

-$150 shipping in the lower 48

Pricing: 

5Ft Bed - $13,195

6Ft Bed - $13,495

Features: 

Integrated Electric Locks
Electric Locks are Integrated into Vehicle’s Central Locking System

Universal Tent T-Slots
Because Proprietary Hardware Is Just Rude. Install Your Choice of 3rd Party Roof Rack Bars.

All-Aluminum Construction
Designed to explore, our tent and camper frames feature an all-aluminum construction, for lightweight strength. Our full-size truck campers range from 340-360lbs depending on bed length and cab height. 

Unobstructed Gear Access
Our camper design features unobstructed side access, allowing you to reach your equipment quickly and effortlessly.

*Financing Available! Please contact us for more information.

Pricing: 

5 Foot Bed - $12,995

6 Foot Bed - $13,295

Features: 

Integrated Electric Locks
Electric Locks are Integrated into Vehicle’s Central Locking System

Universal Tent T-Slots
Because Proprietary Hardware Is Just Rude. Install Your Choice of 3rd Party Roof Rack Bars.

All-Aluminum Construction
Designed to explore, our tent and camper frames feature an all-aluminum construction, for lightweight strength. Our mid-size truck campers range from 320-340lbs depending on bed length and cab height. 

Unobstructed Gear Access
Our camper design features unobstructed side access, allowing you to reach your equipment quickly and effortlessly.

*Financing Available! Please contact us for more information.