REQUEST MY MODEL

Inflate, Deflate, and Equalize air pressure in all 4 tires, all at once. See all of the uses below:

• Air up 1 to 4 tires simultaneously (Less stress on your compressor!)
• Air down 1 to 4 tires simultaneously (Less stress on you!)
• Check all of the tires’ PSI from the manifold (No more continuously bending over checking PSIs)
• Move air from a spare tire into other tires
• Effortlessly equalize tire pressures
• Run different PSI in the front tires from the back tires
• 1-150 psi, 1% accuracy, .1psi precision, back lit digital gauge
• This fits up to155″ wheelbases. To find your wheelbase, measure the distance between your front and rear axle.
• If you need a longer wheelbase, check out the MORRFlate Mega Quad Off Road 4 to 6 Tire Inflation Deflation Kit
• If your air source is in a different location, check out our MORRFlate Extensions
• All MORRFlates fit ARB compressors and PowerTanks “plug n play” If you have a Smittybilt, Viaire, Warn Powerplant, or something modeled after those, you will need a MORRFlate Adapter Kits.
• Read the entire MORRFlate Off Road 4 Tire Inflation Deflation Kit article for more detailed information!

Set Your Pressure™!

• Air up a set of 35″ tires from 10 to 40 psi in under 5min (when combined with a 4 Tire Hose Kit)
• 10.6 CFM dual cylinder compressor at 0 PSI
• 6.5 CFM at 30 psi
• 10-120 psi in Auto Mode
• 1-150 psi in Manual Mode
• Thermal Cutoff Switch & Purge Valve
• 80% duty cycle @ 0psi (45min on, 10min off) (6-8 vehicles) (see duty cycle chart)
• 12v, 90amps peak, ~50amp running
• 14x7x9″ external dimensions
• 70-75 dB noise level from 1ft distance
• Beefed up carrying bag with accessory pockets
• Threaded filter caps so the compressor can be mounted in any direction/orientation (except upside down)
• USA Standard color matched air fitting – Push-to-connect “Universal” Coupler (Works with 1/4″ Industrial, Auto, or Aro fittings)
• WARNING: Compressors get hot! Recommended to wear the included MORRFlate Groovy Gloves while disconnecting air fittings.
• Since the TenSix™ is rated for 10.6 CFM, it is highly recommended to use with a MORRFlate 4 Tire Inflation & Deflation™ Kit to avoid back pressures on the compressor from filling 1 tire at a time.

Gen2 Upgrades (Also, now unique to only MORRFlate):

• Stainless Steel Outlet Hose (for better heat dissipation and heat sinking)
• Purge Valve (to release the internal pressures when done)
• Resized Aluminum heat sinks (upgraded from ABS so they actually fit the cylinders and works as a heat sink)
• Internal aluminum cylinders (upgraded from mild steel to dissipate heat better)
• New piston rings (better material for wear and heat resistance longevity).

Note About This Product: This compressor is not designed for 1 tire at a time. You can still air up a single flat if you need to, but the duty cycle dwindles to 8-10min doing 1 tire at a time. Airing up an entire vehicle, 1 tire at a time, will damage the TenSix. It just simply puts out too much air and is optimized for 4 tires at a time.

Inflate, Deflate, and Equalize air pressure in up to 6 tires, all at once. See all of the uses below:

• Air up 1 to 6 tires simultaneously (Less stress on your compressor!)
• Air down 1 to 6 tires simultaneously (Less stress on you!)
• Check all of the tires’ PSI from one spot (No more continuously bending over checking PSIs)
• Move air from a spare tire into other tires
• Effortlessly equalize tire pressures
• Make all 4-6 tires the same pressure
• Run different PSI in the front tires from the back tires
• 1-150 psi, 1% accuracy, .1psi precision, back lit digital gauge
• This version fits up to a 200″ wheelbase with the air source in the middle of the front or rear bumper areas
• If you need a shorter wheelbase, check out the MORRFlate Quad Off Road 4 Tire Inflation Deflation Kit
• If your air source is in a different location, check out our MORRFlate Extensions
• All MORRFlates fit ARB and PowerTank fittings “plug n play” If you have a Smittybilt, Viaire, Warn Powerplant, or something modeled after those, you will need a MORRFlate Adapter Kits.
• Read the entire MORRFlate Off Road 4 Tire Inflation Deflation Kit article for more detailed information!

The MORRFlate Duo has two 13ft hoses coming off of the manifold for a total length of 26ft from air chuck to air chuck.

Inflate, Deflate, and Equalize air pressure in 2 tires, at once. See all of the uses below:

• Air up 1 to 2 tires simultaneously (Less stress on your compressor!)
• Air down 1 to 2 tires simultaneously (Less stress on you!)
• Check 2 of the tires’ PSI from the manifold (No more continuously bending over checking PSIs)
• Move air from a spare tire into another tire
• Effortlessly equalize tire pressures
• Run different PSI in the front tires from the back tires
• 1-150 psi, 1% accuracy, .1psi precision, back lit digital gauge
• If your air source is in a different location, or you need a little bit more reach, check out our MORRFlate Extensions
• All MORRFlates fit ARB compressors and PowerTanks “plug n play” If you have a Smittybilt, Viaire, Warn Powerplant, or something modeled after those, you will need a MORRFlate Adapter Kits.
• Read the entire MORRFlate Off Road 4 Tire Inflation Deflation™ Kit article for more detailed information!

Inflate, Deflate, and Equalize air pressure in all 4 tires, all at once. See all of the uses below:

• Air up 1 to 4 tires simultaneously (Less stress on your compressor!)
• Air down 1 to 4 tires simultaneously (Less stress on you!)
• Check all of the tires’ PSI from the manifold (No more continuously bending over checking PSIs)
• Move air from a spare tire into other tires
• Effortlessly equalize tire pressures
• Run different PSI in the front tires from the back tires
• 1-150 psi, 1% accuracy, .1psi precision, back lit digital gauge
• This version fits up to a 125″ wheelbase with the air source in the middle of the front or rear bumper areas, or in the center of the side of the vehicle (under seat mounted compressors).
• If you need a longer wheelbase, check out the MORRFlate Quad+ Off Road 4 Tire Inflation Deflation Kit
• If your air source is in a different location, check out our MORRFlate Extensions
• All MORRFlates fit ARB compressors and PowerTanks “plug n play” If you have a Smittybilt, Viaire, Warn Powerplant, or something modeled after those, you will need a MORRFlate Adapter Kits.
• Read the entire MORRFlate Off Road 4 Tire Inflation Deflation Kit article for more detailed information!

• 10.6 CFM dual cylinder compressor at 0 PSI
• 6.5 CFM at 30 psi
• 150 psi rated
• PSI Cutoff Switch (80psi on, 120psi off)
• Thermal Cutoff Switch & Purge Valve
• 80% duty cycle @ 0psi (45min on, 10min off) (6-8 vehicles) (see duty cycle chart)
• 12v, 90amps peak, ~50amp running
• 14x7x9″ external dimensions
• 70-75 dB noise level from 1ft distance
• Beefed up carrying bag with accessory pockets
• Threaded filter caps so the compressor can now be mounted in any direction/orientation (except upside down)
• USA Standard color matched air fitting – Push-to-connect “Universal” Coupler (Works with 1/4″ Industrial, Auto, or Aro fittings)
• WARNING: Compressors get hot! Recommended to wear the included MORRFlate Groovy Gloves while disconnecting air fittings.
• Since the TenSix™ is rated for 10.6 CFM, it is highly recommended to use with a MORRFlate 4 Tire Inflation & Deflation™ Kit to avoid back pressures on the compressor from filling 1 tire at a time.

Gen2 Upgrades (Also, now unique to only MORRFlate):

• Stainless Steel Outlet Hose (for better heat dissipation and heat sinking)
• Purge Valve (to release the internal pressures when done)
• Resized Aluminum heat sinks (upgraded from ABS so they actually fit the cylinders and works as a heat sink)
• Internal aluminum cylinders (upgraded from mild steel to dissipate heat better)
• New piston rings (better material for wear and heat resistance longevity).

Note About This Product: This compressor is not designed for 1 tire at a time. You can still air up a single flat if you need to, but the duty cycle dwindles to 8-10min doing 1 tire at a time. Airing up an entire vehicle, 1 tire at a time, will damage the TenSix. It just simply puts out too much air and is optimized for 4 tires at a time.

The 270 XT Awning Mk2 sets new benchmarks  for a free standing shade awning in terms of overall strength, wind resistance and durability.  The 270 XT Awning Mk2 provides an incredible 8sqm (86sqft) of shade around your 4WD for you to set up your camp kitchen, swags or just a shaded seating/chill out area.

The awning is 2.3m / 90.5 inches in length, weighs only 27.8Kg / 61.3lbs and can easily be set up by one person in about 30 seconds and the pack down is just as simple.

The awning is available in either a Left Hand Side (driver’s side in USA)  or Right Hand Side (passenger side in USA) configuration, please select which version you require from the drop down menu below.

There are 2 Heavy Duty L brackets supplied with the 270 XT Awning Mk2.  One fitment bracket must be attached to the stainless steel head stock at the hinged end of the awning no more than 200mm (7 ⁷/₈inch) from the hinged end, The second bracket must be mounted no less than 1.3m (4′ 3″) from the bracket at the hinged end.  To mount the awning to one of our rooftop tents you will need an Awning To Tent bracket which are sold separately.

Shipping:

Free shipping and installation when purchased at the time of camper purchase

Shipping Included for Orders sent to Utah

Orders shipped elsewhere freight cost will be estimated via phone call.

270 XT MAX Awning Mk2 - Overview

The combination of forward and rear folding arms means the 270 XT MAX Awning Mk2 provides an incredible amount of shade (+/-12m² / 129ft²) around your 4WD for you to set up your camp kitchen, swags or just a shaded seating/chill out area. As you can see from the video the awning is an easy set up by one person in about 60 seconds and the pack down is just as simple.  The 270 XT MAX Awning Mk2 has a heavy duty stainless steel hinge at the rear and front section of the frame with arms that wrap around the rear of your vehicle as well as folding forward to be parallel with the side of the vehicle.

The canvas on the 270 XT MAX Awning is a 315gsm (11.3oz) poly-cotton rip-stop canvas in The Bush Company's traditional olive green colour that is mould and mildew resistant. There is only one seam in the whole canvas section (not including the edges) and the canvas is pre-treated during manufacture for water resistance, but over time if the stitched areas show signs of water ingress this is easily treated with a canvas aqua proof product to seal the stitch holes.  Where the canvas is attached to the ends of the trussed awning arms there is additional triple reinforcement to eliminate chafing, while the front and rear arms slide into a triple stitched canvas sleeve.

The 270 XT MAX Awning Mk2 bag is 460gsm (16.2oz) poly-cotton rip-stop canvas with YKK Zippers.  In contrast to PVC covers, the canvas allows the awning to breath while keeping it dust/dirt free and moisture is able to wick out through the zipper reducing the risk of mould or mildew.  The rip-stop material on the bag also reduces the risk of large running tears in the bag as a result of contact with tree branches, and the front and rear sections of the bag have a double layer of canvas providing extra protection.

The frame of the awning is made from an extruded aluminium alloy composite which has been specifically designed to provide the elasticity, strength and durability we require.  The brackets for the hinges are constructed from stainless steel providing huge strength.  The main truss arms on the awning have been gusseted for additional strength, which enables the awning to be fully free standing without any poles in even strong wind conditions.

We do not supply poles for the awning as it does not need them, but we do supply guy ropes and pegs.  It is recommended that the front and rear arms are pegged down when the awning is deployed to prevent excessive upward movement as these are reinforced but not gusseted.  The guy ropes attach to the 1 tonne webbing straps that are attached to the canvas at the ends of the arms and midway along each canvas section.

In conjunction with the natural rake of the awning, the guy ropes should be used to prevent pooling of water on the canvas and to guide water runoff in preferred places. We do not recommend leaving the awning up unattended during snowfall due to risk of canvas stretching due to excessive weight.

Around the inside edge of the awning is a 50mm (2") thick triple stitched velcro strip which can be used to attach optional awning walls (sold separately) enabling you to fully enclose the area to provide protection from the elements or additional privacy.

Shipping:

Free shipping and installation when purchased at the time of camper purchase

Shipping Included for Orders sent to Utah

Orders shipped elsewhere freight cost will be estimated via phone call.